Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 73)

XR500 Series Programming Guide Digital Monitoring Products

Appendix

Exiting the Diagnostics program

Press the COMMAND key until STOP displays. Press any Select key. The keypad returns to the Status List display.

23.3 Using the 984 Command Function

This feature allows connection to connect to a service receiver, which is used primarily to bring a new account

on-line and upload panel programming completed in Remote Link™.

Note: When not in the Programming Menu, the function 984 + COMMAND can be entered at the keypad, and a

remote options menu appears. This menu contains the following options:

NUMBER: Enter a phone number into the keypad for the panel to dial. Enter any required prexes and area

codes. After completing panel programming in Remote Link, set a trap to seize the panel when it calls. Traps are

set by selecting Panel > Trap. Refer to the Remote Link User’s Guide (LT-0565), or the Remote Link Help File.

Then, from the panel, enter 984 and press the COMMAND key, while the panel is in the Status List. The keypad

display changes to NBR TEST PICKUP. Press the Select key under NBR. Enter the phone number for the service

receiver connected to the Remote Link computer. Press each number key slowly and deliberately. The panel

dials each number as it is pressed. If you make a mistake, press the Back Arrow key. The panel stops dialing and

return to the Status List.

You can enter up to 32 characters for the phone number. Once you have entered 16 characters the LCD display

is full: Press the COMMAND key to enter the nal 16 characters. To enter a # (pound sign) press the ‘0’ then

the fourth (far right) Select key, and to enter an * (asterisk) press the third Select key. Program a pause by

entering the letter P. Program CID message communication by entering the letter T in the rst position. Cancel

call waiting by entering *70P as the rst characters. These characters are counted as part of the allowable 32

characters. Press COMMAND after you enter the phone number.

The panel calls the receiver connected to Remote Link to download the new programming. Remote Link then

traps the panel.

Note: The panel makes ten attempts to reach the receiver. While attempting to contact the receiver, if the

panel needs to send an alarm report, the panel stops dialing and uses the phone line to send its report.

TEST: The panel allows you to perform a Communication Status Test on each component of the panel’s cellular

or network communication paths. While the Status List displays, enter 984 and press the COMMAND key. The

keypad display changes to NBR TEST PICKUP. Press the Select key under TEST to allow the panel to perform

a Communication Status Test. The display prompts the user for a user code to be entered. The user code must

have the authority to perform a System Test.

Upon entry of a Cell or Network path when prompted, the test runs and the results display on the keypad. See

Diagnostic Functions section for a description of the Communication Status results.

PICKUP: The panel picks up the phone line when Remote Link™ calls in. The phone must be ringing before

selecting PICKUP. After completing panel programming in Remote Link, connect to the panel by selecting

Panel > Connect. Refer to the Remote Link User’s Guide (LT-0565), or Help File for complete information about

connecting to panels.

While the panel displays in the status list and the telephone line at the panel rings, enter 984 and press the

COMMAND key. The keypad display changes to NBR TEST PICKUP. Press the Select key under PICKUP to allow the

panel to seize the line. The panel immediately seizes the phone line and sends a carrier tone to the receiver.

A verication process occurs and, if successful, the panel grants remote access to its programming and Event

Buffer.

After the panel has seized the line, send the le from Remote Link by selecting Panel > Send. Remote Link then

uploads the new programming into the panel. You may also Request Events by selecting Panel > Request Events in

Remote Link. The panel begins sending the rst event or access that occurred on or after the start date specied

by Remote Link and nishes by sending the last event or access that occurred on or before the end date specied

by Remote Link. If necessary, a Request Events upload in progress can be cancelled.

Keypad Displays

When the PICKUP option is used, the keypad displays LINE SEIZED. This indicates that the panel has seized

the line and is executing its program. If the line cannot be accessed, or if the PICKUP option is used before all

connect attempts are made, the keypad displays SYSTEM BUSY.

23.4 Using the Walk Test

The XR500 Series panel provides a walk test feature that allows a single technician to test the protection

devices connected to zones on the system. Conduct the Walk Test within 30 minutes of resetting the panel. The

Walk Test automatically ends if no zones are tripped for 20 minutes. TEST IN PROGRESS displays at all keypads

programmed with the same Area Display features. When ve minutes remain, TEST END WARNING displays. The

Walk Test only tests zones assigned to the areas programmed into the keypad in Area Display. If any areas are

armed the Walk Test does not start and SYSTEM ARMED displays.

Note: If the Panic Supervision option is enabled in SYSTEM OPTIONS, the panic button on any programmed key

fob can be tested during the Walk Test. When the panic button is pressed a verication message is sent by the

receiver.

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 73

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500