Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 11)

XR500 Series Programming Guide Digital Monitoring Products

IntroductIon

Introduction

1.1 Before you Begin

This guide provides programming information for the DMP XR500, XR500N, and XR500E panels. After this

Introduction, the remaining sections describe the functions of each programming menu item along with the

available options. Before starting to program, we recommend that you read through the contents of this

guide. The information contained here allows you to quickly learn the programming options and operational

capabilities of the XR500, XR500N, and XR500E panels.

In addition to this guide, you should also read and be familiar with the following XR500 Series documents:

• XR500 Series Installation Guide (LT-0681)

• XR500 Series Programming Sheet (LT-0678)

• XR100/XR500 Security Command

User’s Guide (LT-0683)

Internal Programmer

The panel contains all of its programming information in an on-board processor and does not require an external

programmer. You can perform all programming tasks through a 32-character DMP alphanumeric keypad set to

address one.

Programming Information Sheet

Included with each panel are the Programming Information Sheets. These list the various programming options

and available options for programming the panel. Before starting to program, we recommend you completely ll

out each sheet with the programming options you intend to enter into the panel.

Having completed programming sheets available before entering data helps prevent errors and can shorten the

time you spend programming. Completed sheets also provide you with an accurate panel program record you

can keep on le for future system service or expansion. The remainder of this Introduction provides instructions

for starting and ending a programming session using the alphanumeric keypad.

1.2 Getting Started

Ground Yourself Before Handling the Panel! Touch any grounded metal, such as the enclosure, before touching

the panel to discharge static.

Remove All Power From the Panel! Remove all AC and Battery power from the panel before installing or

connecting any modules, cards, or wires to the panel.

Before starting to program the XR500 Series panel, make sure the panel is properly grounded and AC and battery

power is applied to the appropriate panel terminals. All wiring connections and grounding instructions are

detailed in the XR500 Series Installation Guide (LT-0681).

Program from any Keypad Address or Wireless Keypad

You can program the XR500 panel from any 32-character wireless keypad or hardwired keypad connected to the

panel’s keypad data bus. See the XR500 Installation Guide for keypad addressing and installation information for

hardwired keypads.

Wireless Keypads can be used for panel programming after being programmed in the panel manually or by using

the Wireless Keypad Association operation.

To enable association operation in the keypad, access the Installer Options Menu (3577 (INST)) and select RF

Survey. The keypad logo LEDs turn on Red until association is successful.

To enable association operation in the XR500 panel, reset the panel 3 times within 12 seconds. Allow the panel’s

keypad bus Transmit/Receive LEDs to turn back on between each reset.

For 60 seconds the panel listens for wireless keypads that are in the Installer Options Menu and have not been

programmed, or associated into another panel. Those keypads are assigned to the rst open device position

automatically based upon the order in which they are detected. The keypad logo turns Green to indicate it

has been associated with the panel. See the 9000

Series Wireless Keypad Installation Guide (LT-1107) for

additional information.

Accessing the Programmer

1. Momentarily place the Reset jumper over both

of the J16 pins to reset the panel.

2. Enter the code 6653 (PROG) and press

COMMAND.

3. The keypad displays: PROGRAMMER.

Interface

Card

Expansion

Connector

To enable Wireless Keypad

Association operation:

Reset panel 3 times within

12 seconds.

To access the programmer:

Momentarily place the

Reset jumper over both of

the J16 pins to reset the

panel.

12345678 10 11 12 13 14 15 16 17 18 19

02122 23 24 25 26 27 28

+B BELL GND SMK GNDRED YEL GRN BLK Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9+ Z9– Z10+ Z10–AC –B GND GND GNDGND

K6 K7

Output 1 Output 2

Phone Line

J10

J22

LX-Bus

Battery

Start

J23

J21

RS-232

Power

LED

PROG

Tamper

J16

Reset

Out1 Out2

Outputs 3-6

J11

Ethernet

OVC

Link LED

Activity LED

Figure 1: XR500 Series Panel Showing Reset

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500