Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 29)

XR500 Series Programming Guide Digital Monitoring Products

Device Setup

6.18.4

ACTIVATE ZONE 3

REX? NO YES

Activate Zone 3 Request to Exit

Selecting YES activates the Zone 3 Request to Exit (REX) option.

Selecting NO allows standard zone operation on Zone 3 and displays the ACTIVATE

ONBOARD SPEAKER option. Default setting is NO.

Optionally connect a PIR (or other motion sensing device) or a mechanical switch to Zone

3 to provide REX capability to the system. When Zone 3 shorts, the on-board Form C

relay activates for the programmed number of seconds. During this time, the user can

open the protected door to start the programmed Bypass entry/exit timer. After the

programmed number of seconds, the relay restores the door to its locked state.

The 734/734N/734N-WiFi module provides a bypass-only option for REX on Zone 3. When

Zone 3 opens from a normal state, only a bypass occurs: the on-board relay does not

activate. This bypass-only option uses two methods of REX. The rst REX device provides

the programmed Bypass entry/exit timer. The second REX device, or manual device such

as a door knob, unlocks the door.

An example of the bypass-only conguration is a door to an ofce that is locked 24 hours

a day. Users pass a REX motion detector positioned by the door to begin the programmed

exit timer. Within the programmed number of seconds the user must then manually

activate a second device, such as a REX device or manual door knob, to unlock the door. If

the door is opened after the programmed number of seconds, the zone goes into alarm.

6.18.5

ZN 3 REX STRIKE

TIME: 5

Zone 3 REX Strike Time

Enter the number of REX seconds to elapse. Range is from 5 to 250 seconds. Press any top

row select key to enter the number of seconds. The default is 5 seconds.

6.18.6

ACTIVATE ONBOARD

SPEAKER? NO YES

Activate Onboard Speaker

Select YES to enable the onboard piezo speaker for local annunciation. Select NO to turn

the piezo off for all operations. This does not affect remote annunciator open collector

(RA) operation. The default is NO.

6.18.7

CARD OPTIONS:

DMP

Card Options

Press any top row Select key to display options. Press the select key under DMP,

CUSTOM, or ANY to select that option. Select DMP to indicate the reader sends a 26-

bit DMP data string. Press the COMMAND key to display REQUIRE SITE CODE.

Note: When set to DMP, the 734/734N/734N-WiFi converts 17 bits of the 26-bit data

string into a 5-digit number.

Select CUSTOM if using a non-DMP card or user code length of 6 to 10 digits.

Default is DMP.

Select ANY to allow all card reads to activate the door strike relay. The door strike

relay is activated for the length of time programmed in ZN 3 REX STRIKE TIME. No user

code information is sent to the panel.

  CustomCardDenitions

6.18.8 Weigand Code Length

When using a custom credential, enter the total number of bits to be received in

Wiegand code including parity bits.

Press any top row Select key to enter a number between 1-255 to equal the number of

bits. Default is 26 bits.

Typically, an access card contains data bits for a site code, a user code, and start/stop/

parity bits. The starting position location and code length must be determined and

programmed into the 734/734N/734N-WiFi Module.

CARD OPTIONS:

DMP CUSTOM ANY

WIEGAND CODE

LENGTH: 26

01110101101101010001100111

First Bit

Received

Position = 0

Site Code

Position = 1

Length = 8

User Code

Position = 9

Length = 16

Last Bit

Received

Position = 25

In this example the Wiegand Code Length = 26 bits.

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 29

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500