Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 64)

Digital Monitoring Products XR500 Series Programming Guide

Zone InformatIon

19.11.11

OUTPUT ACTION:

yyy: XXXXXXXX

Output Action

This option allows you to dene the output action (STD, PLS, MOM, TGL, OFF) for

the selected output number. The default is Steady.

yyy = the name of the button being programmed (TOP, BTM, LFT, RGT).

xxxxxxxx = the currently dened output action.

OUTPUT ACTION?

STD PLS MOM TGL

STD (Steady) - The output is turned on and remains on.

PLS (Pulse) - The output alternates one second on and one second off.

The pulsing rate for a Model 716 relay attached to the LX-Bus is 1.6 seconds.

Note: Pulse is not available for key fob button output programmed D1 to D16 or G1

to G20.

MOM (Momentary) - The output is turned on only once for one second.

TGL (Toggle) - The output alternates between the on state and off state. Each

button press toggles the output state.

Note: Toggle is not available for key fob button output programmed G1 to G20.

OUTPUT ACTION?

OFF

OFF (Off) - The output is turned off. If programmed, the output was turned on by

some other means such as another button press, a zone action, or a schedule.

Note: When the output is assigned to PN/PN2 or EM/EM2 button action and is

turned on, the output turns off when any area is disarmed.

When the output action is steady, pulse or toggle and the output is turned on, the

output remains on until:

— the output cutoff time expires

— the output is reset from the keypad menu

— toggled off

19.11.12

NEXT ZONE NO YES

Next Zone

Select YES to return to the ZONE NO: - option to program a new zone. Select NO to

display the Alarm Action option.

Note: All wireless programming is stored in the XR500 Series panel. The 1100X Wireless Receiver obtains the

necessary programming information from the panel each time the receiver powers up, when the programmer

STOP routine is selected or the panel is reset. The receiver memory refresh takes up to 10 seconds to complete

depending on the number of wireless zones programmed and the Red LED remains on during this time. Normal

receiver operation is inhibited during the memory refresh period.

FA Series Wireless

For an FA Series Remote Wireless Receiver set the House Code to 99. See House Code programming in System

Options. Only zones 500 to 699 can be programmed as FA Series Wireless zones for maximum of 200 Wireless

Zones.

For a DMP 1100X Wireless Receiver see section 16.10.

19.12

ZONE INFORMATION

WIRELESS? NO YES

Wireless

Select YES to program a wireless zone connected to an FA Series FA400-DMP Remote

Wireless Receiver. Press the COMMAND key to continue with wireless programming.

19.12.1

CHECK IN TM: 60

Check-in Time

You can set wireless transmitters to check in automatically every 10, 30, or 60

seconds or not at all. To change the 60 second default, press any top row Select key

to display NONE 10 30 60. Select the check-in time you want for this zone.

Note: Refer to the Wireless Check-in and Supervision Time Denitions section of the

Appendix for supervision information.

19.12.2

INT CONT NO YES

Internal Contact

Select YES to use an internal contact on the wireless transmitter. Select NO to use an

external contact. When you select NO, the following two options display.

19.12.3

EOL NO YES

End-of-Line

Select YES to supervise an external contact connected to the wireless transmitter.

At the contact, install a 2.2k Ohm End-of-Line resistor in parallel for Normally Open

contacts and in series for Normally Closed contacts.

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 64

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500