Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 39)

XR500 Series Programming Guide Digital Monitoring Products

SyStem OptiOnS

For example, when Spanish is selected at a keypad, the User Menu and Status List text

display in Spanish at that keypad. When the user later accesses the keypad, pressing

the COMMAND key once displays the option for English, Spanish, or French. Pressing the

COMMAND key again continues to display the Status List text in Spanish. Later on, if

English or French is selected at that keypad, the User Menu and Status List text display in

the selected language at that keypad.

NONE ENG SPN FRN

Select the secondary user language.

NONE = No secondary language options are displayed

ENG = English (ENGLISH)

SPN = Spanish (ESPANOL)

FRN = French (FRANCAIS)

9.15

BYPASS LIMIT 0

Bypass Limit

Enter the maximum number of zones (0 to 8) that can be bypassed in any single area

when that area is being armed at a keypad. If more zones than the limit are in a non-

normal state or already bypassed at arming, arming does not occur and Arming Stopped

displays. The Bypass limit does not affect auto arming, keyswitch arming, or remote

arming. Entering 0 (zero) allows no limit. Default is 0 (zero).

9.16

CARD PLUS PIN:

NO YES

Card Plus PIN (XR500E only)

Select YES to require all users to present a proximity credential and enter a PIN number

wherever user code entry is required for system functions accessed from a keypad. Select

NO to disable Card Plus PIN operation. Default is NO.

Note: The Card Plus PIN option is not designed to operate with All/Perimeter or Home/

Sleep/Away systems.

For an XR500E system using Card Plus PIN, two code entries are required by a user to

operate the system from a keypad. The rst must be a code entered from a Wiegand

interface device (card, fob, etc.) using a reader such as the built-in reader of a DMP

Keypad. An external reader may also be used. The second code (User Pin) is keyed in at

the keypad or could be a second card or fob.

For a Card Plus PIN system, user codes (Card and PIN) are typically administered using

DMP System Link software.

When this option is rst turned on at a keypad, the factory default (user number 9999,

user code 99) must be available to enter the user menu at a keypad to then add user

codes and PIN numbers or to change existing users to add their PIN number. If user 9999

was previously removed, re-enter this user and then set Card Plus Pin = YES. Afterwards,

user 9999 can be removed and the system only allows card plus PIN entries.

Note: Current users of an existing system are immediately affected in that they must

have their user code information changed to add the user PIN.

9.17

WIRELESS

HOUSE CODE: 0

House Code

When using a DMP wireless system, enter a house code between 1 and 50. When using

FA Series wireless enter 99. See Wireless programming in Zone Information. Default is 0

indicating no wireless system is being used.

The DMP house code identies the panel, DMP receiver, and DMP transmitters to

each other. When operating, the DMP receiver listens for transmissions that have the

programmed house code and transmitter serial number.

Note: The exibility of DMP two-way wireless operation allows an existing house code

to be changed in the panel at any time. The transmitters may take up to two minutes to

learn the new house code and continue operation.

Note: When any wireless zone programming is changed in the panel, wireless receiver

zone programming is updated. At that point, all wireless zones display as normal for

approximately 1 minute, regardless of the actual state of the zone.

9.18

DETECT WIRELESS

JAMMING: NO YES

Detect Wireless Jamming

This option displays when the House Code entered is for a DMP 1100 Series Wireless

system (1-50). When enabled and the wireless receiver detects jamming, a trouble or

alarm message displays in the Status List and is sent to the central station receiver.

Select YES to enable jamming messages to display in the Status List. Select NO to disable

jamming messages. Default is NO.

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 39

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500