Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 63)

XR500 Series Programming Guide Digital Monitoring Products

Zone InformatIon

19.11.8

BUTTON

PRESS TIME: XXXXX

Button Press Time

This option species the amount of time (SHORT or LONG) the user must press the

button before the key fob sends a message to the wireless receiver. The default

press time displays. Press any Select key to set the Button Press Time for Arm,

Disarm, Toggle, Status, Output, and Sensor Reset.

Note: The Button Press Time is not programmable on Panic (PN or PN2), Emergency

(EM or EM2) or Unused (UN) zones. For those zones the button press time is always

two (2) seconds.

PRESS TIME:

SHORT LONG

SHORT - Press the button for one-half (1/2) second to send the message to the

wireless receiver.

LONG - Press the button for two (2) seconds to send the message to the wireless

receiver.

19.11.9

ARM/DIS AREAS:

Arm/Disarm Area Selection

In an Area system or Home/Sleep/Away with Guest system, this species the areas

to be armed/disarmed by the Key Fob button being programmed. To select an area

between 1 and 32, enter the area number using the keypad digit keys. Default is no

areas enabled.

In order to arm or disarm selected areas, the Prole assigned to the User Number

needs to have the same area numbers selected. Any area may be selected at Arm/

Disarm Areas but only matching area numbers are armed or disarmed when the

specic button is pressed. For example, in Areas selection, areas 1, 3, and 7 are

selected. In the User Prole Arm and Disarm Areas, areas 1, 2, 4, and 7 are selected.

When the user presses the button to Arm or Disarm area(s), only matching areas 1

and 7 Arm/Disarm.

Note: When more areas are selected at Arm/Disarm Areas than are authorized in

the User Prole, in the future the user can be given access authority to additional

areas through the User Prole without requiring additional panel programming to

select Arm/Disarm Areas. See User Proles in the Appendix or refer to the XR500

Series User’s Guide (LT-0683).

ARM AREAS: PERIM

In an All/Perimeter or Home/Sleep/Away system, this species the area to be armed

by the Key Fob button being programmed. For All/Perimeter systems, choose PERIM

or ALL, for Home/Sleep/Away or Home/Away systems, choose HOME, SLEEP, or AWAY.

Note: Areas 3 and higher in an All/Perimeter system, and areas 4 and higher in a

Home/Sleep/Away system are not available for use.

After selecting the areas, for one-button key fobs the Zone No.: option displays. For

two-button or four-button key fobs, the Key Fob Button Selection option displays to

program additional buttons.

19.11.10

OUTPUT NO: XXX

Output Number

You can specify a relay output to operate when OUT (Output), PN (Panic), PN2

(Panic 2), EM (Emergency), or EM2 (Emergency 2) is selected for a key fob Button

Action and the button is pressed. Valid range is 1 to 6, 500 to 999,

D1 to D16, or G1 to G20. For an output turned on by a PN, PN2, EM, or EM2 button

action, the output turns off when any area is disarmed.

To enter an output number, press a top row Select key followed by the output

number. Press the COMMAND key.

1 2 ... 58 59 60 61 62 63 64 65 66 67 68 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 63

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500