Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 54)

Digital Monitoring Products XR500 Series Programming Guide

AreA InformAtIon

18.5

CLS CHK NO YES

Closing Check

Select YES to enable the panel to verify that all areas in the system are armed after

permanent or extended sched ules ex pire. If the Clos ing Check nds any areas disarmed

past the sched uled time, the keypads selected to display System Trouble Status displays

CLOSING TIME! and emits a steady beep. When Area Schedules is set to YES in Area

Information, the specic area and name display followed by — LATE.

When Auto Arm is NO, if within ten minutes the system is not armed or if the schedule

is not extended, a Late to Close report is sent to the SCS-1R Receiver. When Auto Arm is

YES, the area arms. See Automatic Arming section.

If the area becomes disarmed outside of any schedule, the Closing Check sequence

occurs after the Late Arm Delay time. See Late Arm Delay.

When Closing Check is NO and Auto Arm is YES, the system immediately arms when the

schedule expires. No warning tone occurs.

In addition, when Closing Check is NO, the option to extend a schedule does not display

when the schedule expires.

18.6

CLS CODE NO YES

Closing Code

When YES is selected, a code number is required for system arming. If NO is selected, a

code number is not required for system arming.

18.7

ANY BYPS NO YES

Any Bypass

When YES is selected, zones can be bypassed without a code number during the arming

sequence. A code number is always required to use the Bypass Zones option from the

menu.

18.8

AREA SCH NO YES

Area Schedules

Select YES to allow each area to set its own shift schedules 1 to 4. Enter NO to provide

one set of schedules for this system.

Note: Area Schedules are not designed to operate with All/Perimeter or Home/Sleep/

Away systems.

18.9

EARLY AMBUSH: 0

Early Morning Ambush (XR500N/XR500E only)

Enter the number of minutes (1 to 15) before a silent alarm (Early Morning Ambush S33) is

sent to the central station using the area 1 account number. Enter 0 (zero) to disable this

option.

When a user code is entered to disarm area 1 at a keypad or reader with Access

Areas assigned to area 1, the same or different user code must be entered within the

programmed number of minutes to prevent an ambush message from being sent to the

receiver. The second user code also must have authority to disarm area 1.

In addition, a zone activation with Alarm Action Message C also cancels the Early Morning

Ambush timer and stops an Ambush message from being sent to the receiver. See Report

to Transmit section in Zone Information.

The keypad does not display any indication that the ambush timer is running.

Indications can be provided by assigning an output number to Entry Out and Ambush Out

in Output Options. Entry Out turns on one minute before the timer expires and turns off

at expiration. Ambush Out turns on at the timers’ expiration and turns off when Sensor

reset is performed.

18.10

AREA NO: -

Area Number

Enter the number of the area to program. After entering the area number, press

COMMAND to enter the area name. Only Area systems allow the area name to be

changed.

Note: When All/Perimeter or Home/Sleep/Away is selected as the system type, the Area

Number does not display.

18.10.1

All/Perimeter Programming

When All/Perimeter is selected as the system type, program the Interior and Perimeter

areas as needed.

18.10.2

INT BDRM PERIM

Home/Sleep/Away Programming

When Home/Sleep/Away is selected as the system type, program the Interior, Bedroom,

and Perimeter areas as needed.

INT PERIM

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 54

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500