Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 60)

Digital Monitoring Products XR500 Series Programming Guide

Zone InformatIon

DMP Wireless

For a DMP 1100X Wireless Receiver set the House Code from 1 to 50. See House Code programming in System

Options. Zones 500 through 999 can be programmed as Wireless zones. Set the XR500 Series panel J23 jumper to

X to enable on-board DMP Wireless operation. Briey reset the panel using the J16 jumper to activate Wireless

operation. Refer to the XR500 Series Installation Guide (LT-0681).

For an 1100 Series Key Fob see section 19.11.

For an FA Series Remote Wireless Receiver see section 19.12.

NOTE: All wireless programming is stored in the XR500 Series panel. The 1100X Wireless Receiver obtains the

necessary programming information from the panel each time the receiver powers up, when the programmer

STOP routine is selected or the panel is reset. The receiver memory refresh takes up to 10 seconds to complete

depending on the number of wireless zones programmed and the Red LED remains on during this time. Normal

receiver operation is inhibited during the memory refresh period.

19.10 Wireless

Select YES to program this zone as a DMP wireless zone. You must program the

wireless House Code prior to adding DMP wireless zones to the system. See House Code

programming in System Options. Default is NO.

19.10.1

TRANSMITTER

SERIAL#: XXXXXXXX

Serial Number Entry

Enter the eight-digit serial number found on the wireless device.

ALREADY IN USE

ZONE NUMBER: XXX

This message displays when the serial number is already programmed for another

zone. The programmed zone number displays.

19.10.2

TRANSMITTER

CONTACT:XXXXXXXX

Contact

This option displays if the serial number entered is for an 1101 or 1103 Universal

Transmitter or 1114 Wireless Four-Zone Expander. Press any top row key to select

the contact.

TRANSMTR CONTACT

INT EXT

This option displays when programming an 1101 or 1103 Transmitter. Select INT to

use the internal reed switch contacts. Select EXT to connect an external device to

the 1101 or 1103 terminal block. Default is INTERNAL.

By allowing both of the Model 1101 or 1103 transmitter contacts (INT and EXT) to be

used at the same time, two zones may be programmed from one transmitter. When

using both contacts, you must use consecutive zone numbers. Zones 531 and 532 or

zones 890 and 891 are acceptable zone assignments.

For example, program transmitter serial number 01345678 as Zone 521 with an INT

contact type and Zone 522 with an EXT contact type. The same serial number is

used for both zones.

Note: When using the 1103 Universal Transmitter in a UL listed Commercial Burglary

installation, the external contact cannot be used.

TRANSMTR CONTACT

1 2 3 4

This option displays when programming the 1114 Wireless Four-Zone Expander with

four input contacts. The same serial number is used for all four contacts. Select the

contact number to program. When using the contacts, you must use consecutive

zone numbers. Default is Contact 1.

For example, use serial number 08345678 to program Contact 1 for Zone 561,

Contact 2 for Zone 562, Contact 3 for zone 563, and Contact 4 for zone 564.

A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.

ALREADY IN USE

ZONE NUMBER: XXX

This message displays when the Contact is already programmed for another zone.

The programmed zone number displays.

ZONE INFORMATION

NORM OPN NO YES

This option only displays when EXT is selected as the Contact type. For external

devices connected to the 1101 or 1103 terminal block, select NO to use normally

closed (N/C) contacts. Select YES to use normally open (N/O) contacts. Default is

NO.

Note: For UL listed installations, set Normally Open to NO.

19.10.3

TRANSMITTER

SUPRVSN TIME: 240

Supervision Time

Press any top row key to select the supervision time required for the wireless zone.

Press COMMAND to accept the default time. Default is 240 minutes.

Note: Refer to the Wireless Check-in and Supervision Time Denitions section of the

Appendix for supervision information.

ZONE INFORMATION

WIRELESS? NO YES

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 60

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500