Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 51)

XR500 Series Programming Guide Digital Monitoring Products

PC Log RePoRts

PC Log Reports

17.1

PC LOG REPORTS

PC Log Reports

This section allows you to program the types of PC Log Reports the panel sends through

the 462N Network Interface Card or through the J21 Serial Connector directly on the

XR500 Series panel. The reports include information such as the type of activity, time

and date of the activity, and user name and number. These data reports can be accessed

from a PC using the Advanced Reporting Module. See the Installation Guide (LT-0681) for

detailed J21 setup information or the User’s Guide (LT-0683) for more information.

Note: The network connection that sends PC Log Reports is not monitored for network

trouble. The PC Log Reports option should NOT replace the primary communication

method or act as a backup communication method.

If there is trouble with the network connection, the panel continues to attempt to

send the PC Log Reports until the connection is reestablished. The panel then sends the

reports. A Network Trouble message is NOT sent if the connection is lost since this report

tool is not designed to be monitored by a receiver. The PC Log Reports have the lowest

priority of panel reports sent.

For information about the 462N card capabilities with PC Log Reports and Network

Communication method, see 462N Card Examples in the Appendix.

Note: The PC Log Address String entered CANNOT be the same as that entered in

Communication.

17.2

COMM TYPE: NONE

Communication Type

NONE NET 232

Select the Communication Type to send the PC Log Reports. Default is NONE.

17.3

NET IP ADDRESS

Net IP Address

This option displays when the Communication Type for PC Log Reports is NET. Enter the

IP address containing up to 16 characters. The Net IP Address must be unique and cannot

be duplicated on the network. Enter all 12 digits and leave out the periods. For example,

enter IP address 192.168.0.250 as 192168000250. The periods display automatically.

17.4

NET PORT 2001

Net Port

This option displays when Communication Type for PC Log Reports is Net. Enter the Port

number. Valid numbers are from 0 to 65535. Default is 2001.

17.5

232 COMM PORT: O

232 Communication Port

This option displays when Communication Type for PC Log Reports is 232. To enable PC

Log Reports, select either the on-board connector (O) or select A, B, C, D or E for the

corresponding slot in use on the DMP Model 462N Network Interface card. The slots are

labeled from left to right, beginning with A. Default is O.

Set the XR500 Series panel J23 jumper to R and briey reset the panel using the J16

jumper to activate RS-232 operation.

17.6

232 SETUP:

232 Setup

This option displays when Communication Type for PC Log Reports is 232. Enter up to 32

characters.

17.7

ARM/DIS NO YES

Arm and Disarm Reports

Sends arming, disarming and Late to Close events. Includes the area number, name and

action, the user number and name, and the time and date.

17.8

ZONE NO YES

Zone Reports

Sends changes in the status of active zones. Includes the zone number, name, type, the

action (alarm, trouble, bypass, etc.), user number (if applicable), and area name. For a

Walk Test, Verify and Fail messages are sent for each zone.

17.9

USR CMDS NO YES

User Command Reports

Sends user code changes, schedule changes, and door access denied events.

17.10

DOOR ACS NO YES

Door Access Reports

Sends door access activity: door number, user number and name, and time and date.

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 51

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500