Digital Monitoring Products Canadain XR500 Manual de instrucciones descargar pdf (Pagina 67)

XR500 Series Programming Guide Digital Monitoring Products

Zone InformatIon

19.21

RETARD NO YES

Zone Retard Delay

When you select YES, the zone operates with the zone retard delay. The retard func tions

only in zone short condi tions.

The zone must re main shorted for the full length of the re tard de lay before the panel

recognizes its condition. If you select NO, the zone operates without a retard delay.

Note: For UL installations, Zone Retard Delay shall not be used for burglary zones.

19.22

PRESGNL KEYPADS:

Presignal Keypad Addresses

You can enable any combina tion of keypad addresses to sound a presignal tone during the

time a zone is in retard delay. The presignal tone si lences when the zone restores or the

re tard delay expires.

To en able a presignal ad dress, press any top row Select key followed by the number of

the keypad address. You can enable the presignal for all 16 keypad addresses. To disable

a presignal address press the matching number digit again. Press the COMMAND key when

the address selection is complete. The Presignal option is only displayed when Retard is

selected as YES.

19.23

FAST RSP NO YES

Fast Response

Select YES to provide a zone response time of 167ms. Select NO to provide a normal zone

response time of 500ms. Zones 500 to 999 have a xed response time and do not display

this option.

19.24

CRS ZONE NO YES

Cross Zone

Select YES to enable cross zoning for this zone. Cross zoning requires one or more armed

zones to fault within a programmed time before an alarm report is sent to the receiver.

When the rst cross zoned zone trips, the cross zone time specied in System Options

begins to count down. When a second cross zoned zone trips or the rst zone trips a

second time before the end of the count down, the bell action assigned to the zone

activates and the panel sends an alarm report for both zones.

If no other cross zoned zone trips before the cross zone time expires, the panel sends

only a zone fault report to the receiver.

Cross zoning is not compatible with all zone types: You can not enable cross zoning for

Fire verify zones or for any Fire zones that have Retard Delay enabled.

Note: For UL Installations, Cross Zoned zones must protect the same area.

19.25

PRIORITY NO YES

Priority

Select YES to provide additional protection for the premises by requiring this zone to be

in a normal condition before its assigned area can be armed.

19.26 Fire Panel Slave Input

This option is available on Fire Zones (FI) only and allows a re zone the ability to

provide slave communication operation for a separate re alarm control panel. If YES,

this zone will transmit a restoral immediately when restored by the re panel being

monitored. A sensor reset is not required to generate the restoral message.

If NO, this zone will operate as a standard re type zone and a sensor reset is required

before the zone will return to normal. Default is NO.

19.27 Area Follower

Allows Night, Day, Aux 1, or Aux 2 burglary zones to be delayed by following any exit or

entry delay that is currently running in the area that is specied. Default is 0.

19.28 Zone Real-Time Status

Selecting YES allows Real-Time Status reports, such as Door Open or Closed with zone

number, to be sent using PC Log reporting. Selecting NO disables Real-Time Status for this

zone. Default is NO.

19.29

ZONE AUDIT DAYS:

Zone Audit Days

Enter the number of days (0 to 365) allowed to elapse without the zone being tripped

before a fault message is sent. The message is sent to the receiver(s) programmed to

receive Supervisory/Trouble Reports at 10:00 am following the expiration of the timer.

Each time the zone is tripped, the Zone Audit Days timer restarts and begins to countdown

the number of days programmed. After the countdown expires, a fault message is sent

and the Zone Audit Days timer restarts and begins to countdown the number of days

programmed. Available for all zone types except re and re verify. Enter 0 (zero) to

disable this function. Default is 0 (zero).

FOLLOW AREA: 0

ZONE REAL-TIME

STATUS

NO YES

FIRE PANEL SLAVE

INPUT: NO YES

1 2 ... 62 63 64 65 66 67 68 69 70 71 72 ... 83 84

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Manual de instrucciones Pagina 67

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500