Digital Monitoring Products Canadian XR100 Manual de instrucciones descargar pdf (Pagina 68)

Digital Monitoring Products XR100 Series Programming Guide

Appendix

Exiting the Diagnostics program

To exit the Diagnostics function, press the COMMAND key until STOP displays. Press any Select key to exit

thediagnosticsfunction.ThekeypadreturnstotheStatusListdisplay.

21.3 Using the 984 Command Function

Thisfeatureallowsyoutoconnecttoaservicereceiver,primarilyusedtobringanewaccounton-line,

uploadpanelprogrammingcompletedinRemoteLink™,andperformaCommunicationStatusTestforCELL

andNETpaths.

Note:WhennotintheProgrammingMenu,thefunction984+COMMANDcanbeenteredatthekeypad,and

a remote options menu appears. This menu contains the following options:

NUMBER:

The panel allows you to enter into the keypad a phone number you want the panel to dial.

Enteranyrequiredprexesandareacodes.

AftercompletingpanelprogramminginRemoteLink,setatrap

toseizethepanelwhenitcalls.TrapsaresetbyselectingPanel>Trap.RefertotheRemoteLinkUser’s

Guide(LT-0565),ortheRemoteLinkHelpFile.

Then,fromthepanel,enter984andpresstheCOMMANDkey,whilethepanelisintheStatusList.The

keypad display changes to NBR TEST PICKUP. Press the Select key under NBR.Enterthephonenumber

fortheservicereceiverconnectedtotheRemoteLinkcomputer.Presseachnumberkeyslowlyand

deliberately. The panel dials each number as it is pressed. If you make a mistake, press the Back Arrow key.

ThepanelstopsdialingandreturntotheStatusList.

Youcanenterupto32charactersforthephonenumber.Onceyouhaveentered16characterstheLCD

displayisfull:PresstheCOMMANDkeytoenterthenal16characters.Toentera#(poundsign)pressthe

‘0’thenthefourth(farright)Selectkey,andtoenteran*(asterisk)pressthethirdSelectkey.Program

apausebyenteringtheletterP.ProgramCIDmessagecommunicationbyenteringtheletterTintherst

position.Cancelcallwaitingbyentering*70Pastherstcharacters.Thesecharactersarecountedaspart

oftheallowable32characters.PressCOMMANDafteryouenterthephonenumber.

ThepanelcallsthereceiverconnectedtoRemoteLinktodownloadthenewprogramming.RemoteLink

then traps the panel.

Note: The panel makes ten attempts to reach the receiver. While attempting to contact the receiver, if the

panel needs to send an alarm report, the panel stops dialing and uses the phone line to send its report.

TEST: ThepanelallowsyoutoperformaCommunicationStatusTestoneachcomponentofthepanel’s

cellularornetworkcommunicationpaths.WhiletheStatusListdisplays,enter984andpresstheCOMMAND

key. The keypad display changes to NBR TEST PICKUP. Press the Select key under TEST to allow the panel

to perform a Communication Status Test. The display prompts the user for a user code to be entered. The

user code must have the authority to perform a System Test.

UponentryofaCellorNetworkpathwhenprompted,thetestrunsandtheresultsdisplayonthekeypad.

See Diagnostic Functions section for a description of the Communication Status results.

PICKUP: ThepanelpicksupthephonelinewhenRemoteLink™callsin.Thephonemustberinging

beforeselectingPICKUP.

AftercompletingpanelprogramminginRemoteLink,connecttothepanelby

selectingPanel>Connect.RefertotheRemoteLinkUser’sGuide(LT-0565),orHelpFileforcomplete

information about connecting to panels.

Whilethepaneldisplaysinthestatuslistandthetelephonelineatthepanelrings,enter984andpress

the COMMAND key. The keypad display changes to NBR TEST PICKUP. Press the Select key under PICKUP

to allow the panel to seize the line. The panel immediately seizes the phone line and sends a carrier

tonetothereceiver.Avericationprocessoccursand,ifsuccessful,thepanelgrantsremoteaccesstoits

programmingandEventBuffer.

Afterthepanelhasseizedtheline,sendthelefromRemoteLinkbyselectingPanel>Send.RemoteLink

thenuploadsthenewprogrammingintothepanel.YoumayalsoRequestEventsbyselectingPanel>Request

EventsinRemoteLink.Thepanelbeginssendingthersteventoraccessthatoccurredonorafterthestart

datespeciedbyRemoteLinkandnishesbysendingthelasteventoraccessthatoccurredonorbeforethe

enddatespeciedbyRemoteLink.Ifnecessary,aRequestEventsuploadinprogresscanbecancelled.

Keypad Displays

When either the RMT or PICKUP options are used, the keypad displays LINE SEIZED. This indicates that

the panel has seized the line and is executing its program. If the line cannot be accessed, or if the RMT or

PICKUP options are used before all connects attempts are made, the keypad displays SYSTEM BUSY.

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 77 78

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadian XR100 Manual de instrucciones Pagina 68

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadian XR100