Digital Monitoring Products Canadian XR100 Manual de instrucciones descargar pdf (Pagina 58)

Digital Monitoring Products XR100 Series Programming Guide

Zone InformatIon

TRANSMTR CONTACT

1 2 3 4

Thisoptiondisplayswhenprogrammingthe1114WirelessFour-ZoneExpander

with four input contacts. The same serial number is used for all four contacts.

Select the contact number to program. When using the contacts, you must use

consecutive zone numbers. Default is Contact 1.

Forexample,useserialnumber08345678toprogramContact1forZone561,

Contact2forZone562,Contact3forzone563,andContact4forzone564.

A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.

ALREADY IN USE

ZONE NUMBER: XXX

This message displays when the Contact is already programmed for another

zone. The programmed zone number displays.

ZONE INFORMATION

NORM OPN NO YES

ThisoptiononlydisplayswhenEXTisselectedastheContacttype.Forexternal

devicesconnectedtothe1101or1103terminalblock,selectNOtouse

normallyclosed(N/C)contacts.SelectYEStousenormallyopen(N/O)contacts.

Default is NO.

Note:ForULlistedinstallations,setNormallyOpentoNO.

18.10.3

TRANSMITTER

SUPRVSN TIME: 240

Supervision Time

Press any top row key to select the supervision time required for the wireless

zone.PressCOMMANDtoacceptthedefaulttime.Defaultis240minutes.

SELECT MINUTES:

0 3 60 240

Press the Select key under the required number of minutes. The transmitter

must check in at least once during this time or a missing condition is indicated

for that zone. 1100 Series transmitters automatically checkin based on the

supervision time selected for the wireless zone, no additional programming

is needed. If two zones share the same transmitter, the last programmed

supervisiontimeisstoredasthesupervisiontimeforbothzones.Zero(0)

indicates an unsupervised transmitter.

 The3minutesupervisiontimeisonlyavailableforzonetypesofFire(FI),Fire

Verify(FV),andSupervisory(SV).

Note: When the panel is reset or a receiver is installed or powered down and

powered up, the supervision timer restarts for all wireless zones.

18.10.4

LED OPERATION

NO YES

LED Operation

SelectYEStoturnonan1142Hold-uptransmitterLEDduringPanicor

Emergencyoperation.SelectNOtoturntheLEDoffduringPanicorEmergency

operation.TheLEDalwaysoperateswhenthetransmittercaseisopenandthe

tamperisfaulted.DefaultisYES.

Note:ForULlistedholdupinstallations,setLEDOperationtoNO.

18.10.5

DISARM DISABLE

NO YES

Disarm/Disable

SelectYEStodisablethezonetrippedmessagefroman1103UniversalTransmitter

(Version107orhighersoftware)or1126/1127PIRsduringthedisarmedperiod.

When disarmed, the transmitter or PIR only sends supervision, tamper, and low

battery messages to extend transmitter battery life. For 1103Transmitters,a zone

tripped message is sentifthezoneremainstrippedfor20seconds.SelectNOto

always send zone tripped messages in addition to supervision, tamper, and low

battery.DefaultisYES.

18.10.6

WIRELESS PIR

PULSE COUNT: 4

PIR Pulse Count

Selectthenumberofinfraredpulses(2or4)the1126or1127PIRshouldsense

before sending a short message to the 1100X Series Receiver. Default is 4.

18.10.7

WIRELESS PIR

SENSITIVITY:LOW

PIR Sensitivity

Selectthesensitivitysettingforthe1126or1127PIR.SelectingLOWsets

thePIRtooperateat75%sensitivityforinstallationsinharshenvironments.

SelectingHIGHsetsthePIRtomaximumsensitivity.DefaultisLOW.

18.10.8

NEXT ZONE NO YES

Next Zone

SelectYEStoreturntotheZONENO:-optiontoprogramanewzone.SelectNO

to display the Alarm Action option.

ZONE INFORMATION

WIRELESS? NO YES

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 77 78

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadian XR100 Manual de instrucciones Pagina 58

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadian XR100