Digital Monitoring Products Canadian XR100 Manual de instrucciones descargar pdf (Pagina 57)

XR100 Series Programming Guide Digital Monitoring Products

Zone InformatIon

18.9

NEXT ZN? NO YES

Next Zone

SelectYEStoterminatezoneprogramming.ThedisplayreturnstoZoneNumber,

allowing you to enter a new zone number. Select NO to make alter ations to the

AlarmActionforazone.AlarmActionisdenedbeginningwithsection15.12.

Toprogramzonesforwirelessoperation,selectNOattheNEXTZONE-NOYES

option.TheWIRELESSNOYESoptiondisplays.Ifthezoneyouareprogramming

isintendedforwirelessdevices,selectYES.SelectNOtocontinueprogramming

non-wirelesszonesinthe500to599range.

•Zones400to449canbeprogrammedfor1100SeriesKeyFobs.

•Zones500through599canbeprogrammedforDMPWireless.

DMP Wireless

For a DMP 1100X Wireless Receiver settheHouseCodeto1-50.SeeHouseCodeprogramminginSystem

Options.Zones500through599canbeprogrammedasWirelesszones.SettheXR100SeriespanelJ23

jumpertoXtoenableDMPWirelessoperation.Afterpower-up,brieyresetthepanelusingtheJ16jumper

toactivateWirelessoperation.RefertotheXR100SeriesInstallationGuide(LT-0899).

For an 1100 Series Key Fob see section 15.11.

NOTE: All wireless programming is stored in the XR100 Series panel. The 1100X Wireless Receiver obtains

the necessary programming information from the panel each time the receiver powers up, when the

programmer STOP routine is selected or the panel is reset. The receiver memory refresh takes up to 10

secondstocompletedependingonthenumberofwirelesszonesprogrammedandtheRedLEDremainson

during this time. Normal receiver operation is inhibited during the memory refresh period.

18.10 Wireless

SelectYEStoprogramthiszoneasaDMPwirelesszone.Youmustprogramthe

wireless House Code prior to adding DMP wireless zones to the system. See House

Code programming in System Options. Default is NO.

18.10.1

TRANSMITTER

SERIAL#: XXXXXXXX

Serial Number Entry

Entertheeight-digitserialnumberfoundonthewirelessdevice.

ALREADY IN USE

ZONE NUMBER: XXX

This option displays when the serial number is already programmed for another

zone. The programmed zone number displays.

18.10.2

TRANSMITTER

CONTACT:XXXXXXXX

Contact

Thisoptiondisplaysiftheserialnumberenteredisforan1101or1103Universal

Transmitteror1114WirelessFour-ZoneExpander.Pressanytoprowkeyto

select the contact.

TRANSMTR CONTACT

INT EXT

Thisoptiondisplayswhenprogrammingan1101or1103Transmitter.SelectINT

tousetheinternalreedswitchcontacts.SelectEXTtoconnectanexternal

devicetothe1101or1103terminalblock.DefaultisINTERNAL.

ByallowingbothoftheModel1101or1103transmittercontacts(INTand

EXT)tobeusedatthesametime,twozonesmaybeprogrammedfromone

transmitter. When using both contacts, you must use consecutive zone numbers.

Zones531and532orzones590and591areacceptablezoneassignments.

Forexample,programtransmitterserialnumber01345678asZone521with

anINTcontacttypeandZone522withanEXTcontacttype.Thesameserial

number is used for both zones.

Note:Whenusingthe1103UniversalTransmitterinaULlistedCommercial

Burglary installation, the external contact cannot be used.

ZONE INFORMATION

WIRELESS? NO YES

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 77 78

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadian XR100 Manual de instrucciones Pagina 57

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadian XR100