Digital Monitoring Products Canadian XR100 Manual de instrucciones descargar pdf (Pagina 34)

Digital Monitoring Products XR100 Series Programming Guide

SyStem OptiOnS

8.7

ACCESS KEYPADS:

Access Keypads

Selectthekeypadaddresses(1through8)thatsenddooraccessreportstothe

receiver.Enterthekeypadnumberusingthedigitkeys.Anasterisknexttothe

number indicates that the keypad is selected.

A report is sent with each door access made from the selected keypads. Keypads at

addresses not selected still operate the door relay but do not send access reports.

The report includes the user number, user name, keypad address, and device name.

8.8

AMBUSH NO YES

Ambush

YESallowsanambushreporttobesentanytimeusercodenumber1isenteredat

a keypad. NO disables the ambush report and allows user number 1 to operate the

same as all other codes.

System Options

9.1

SYSTEM OPTIONS

System Options

Thissectionallowsyoutoselectsystem-wideparameters.

9.2

SYSTEM: AREA

System

This option allows you to program how the areas operate for arming and disarming.

The options you can choose are listed below:

AREA - All eight areas can be programmed and operated independently.

ALL/PERIMETER -Area1isthePerimeterandArea2istheInterior.

HOME/SLEEP/AWAY -Area1isthePerimeter,Area2istheInterior,andArea3is

theBedrooms.WiththeHOME/SLEEP/AWAYoption,theusercan:

1.SelectHOMEtoarmjusttheperimeter.

2.SelectSLEEPtoarmtheperimeterandinterior(nonbedroomareas).

3.SelectAWAYtoarmallthreeareas.

Note:AHome/Sleep/Awaysystemcanbeconguredtouseallthreeareasor

only use the Home and Away areas.

HOME/SLEEP/AWAY WITH GUEST- This allows the alarm system to be divided into

amainhouseHOME/SLEEP/AWAYsystemandaguesthousethatisalsosetupasa

HOME/SLEEP/AWAYsystem.

Areas1,2,and3arethePerimeter,Interior,andBedroomsfortheMainhouse

system.Areas4,5,and6arethePerimeter,Interior,andBedroomsfortheGuest

system. These areas are automatically assigned per system and cannot be changed.

SeeDisplayAreasinDeviceSetuptoassignkeypadstoasystem.Zonesareassigned

toasystembyassigningthesystem’sareanumberstothezoneinZoneInformation

programming.

WheneitherAll/PerimeterorHome/Sleep/Awayisselected,theareanamesare

automaticallyassignedandcannotbemodied.

Note:Areas3-6inanAll/Perimetersystemandareas4-6inaHome/Sleep/Away

system are not available for use and are initialized.

9.3

INST ARM NO YES

Instant Arming

WhenYESisselected,thearmingkeypaddisplaysINSTANTforselectionduringthe

exit countdown delay when arming fewer than all areas of the system. At the time

instant arming is selected, any entry and exit delays programmed for the areas being

armed are ignored. The entry delay for previously armed areas is not affected by

instant arming. When NO is selected, INSTANT does not display during arming. Default

isNOforanAreaSystem,andYESforanAll/PerimeterorHome/Sleep/Awaysystem.

9.4

CLS WAIT NO YES

Closing Wait

WhenYESisselected,thekeypaddisplaysONEMOMENT...whilewaitingforan

acknowledgementfromthereceiverbeforearmingtheselectedarea(s)and

performingaBellTest(ifselected).ExitdelaysbeginaftertheClosingWait.

Opening/ClosingreportsmustbeYEStoenableClosingWait.

AREA A/P H/A GST

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 77 78

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadian XR100 Manual de instrucciones Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadian XR100