Digital Monitoring Products Canadian XR100 Manual de instrucciones descargar pdf (Pagina 59)

XR100 Series Programming Guide Digital Monitoring Products

Zone InformatIon

1100 Series Key Fobs

For an 1100 Series Key FobsettheHouseCodeto1-50.SeeHouseCodeprogramminginSystemOptions.

Onlyzones400to449canbeprogrammedas1100SeriesKeyFobzones.Refertothe1100SeriesKeyFob

ProgrammingSheet(LT-0706)andthe1100SeriesKeyFobInstallGuide(LT-0703)asneeded.Thefollowing

programmingcontinuesfromtheZoneNumberSectionwhenzone400-449isselected.

To operate arming and disarming properly, the Key Fob should be assigned to a User Number with

appropriate area assignments, however, the User Number does not have to exist at the time the Key

Fob is programmed. The Key Fob User Number can be added later by the User.

Note: Key Fobs have not been investigated by UL and are not intended for UL listed applications.

ThefollowingprogrammingcontinuesfromtheZoneNumbersectionwhenzone400-449isselected.

18.11.1

KEY FOB USER

NUMBER: XXXX

Key Fob User Number

EntertheUserNumber(1-9999)usedtoidentifytheKeyFobuserandtheir

arming and disarming authority at the receiver and panel. Default is blank.

DisplayswhentheUserNumberentereddoesnotexistinUserCode

programming. The key fob can be added, but the user must eventually be

created to cause the key fob to operate.

18.11.2

TRANSMITTER

SERIAL#: XXXXXXXX

Key Fob Serial Number

Entertheeight-digitserialnumberfoundonthewirelessdevice.

18.11.3

TRANSMITTER

SUPRVSN TIME: 0

Key Fob Supervision Time

Press any top row key to select the supervision time required for the key fob

zone. Press COMMAND to accept the default time. Default is 0 for key fobs.

SELECT MINUTES:

0 60 240

Press the Select key under the required number of minutes. The key fob must

check in at least once during this time or a missing condition is indicated for

that zone. 1100 Series key fobs automatically checkin based on the supervision

time selected for the wireless zone, no additional programming is needed.

Zero(0)indicatesanunsupervisedtransmitter.

Note: When the panel is reset or a receiver is installed or powered down and

powered up, the supervision timer restarts for all wireless zones.

18.11.4

NO. OF KEY FOB

BUTTONS: X

Number of Key Fob Buttons

Enterthenumberofbuttons(1,2,or4)ontheKeyFobbeingprogrammed.

Note:Ifthekeyfobisaone-buttonmodel,programmingcontinuesatthe

ButtonActionsection.Defaultbuttonassignmentforone-buttonkeyfobsisa

PanicAlarm(PN)withnooutputassigned.

18.11.5

BUTTON:

TOP BTM LFT RGT

Key Fob Button Selection (Four Buttons)

ThisoptiononlydisplaysiftheKeyFobbeingprogrammedisafour-button

model. Press the Select key under the Key Fob button to program. The following

listidentiesthedefaultbuttonassignments:

TOP Arming with no areas assigned

BTM Disarming with no areas assigned

LFT PanicAlarm(PN)withnooutputassigned

RGT ArmingwithArea1assigned

18.11.6

BUTTON:

TOP BTM

Key Fob Button Selection (Two Buttons)

ThisoptiononlydisplaysiftheKeyFobbeingprogrammedisatwo-button

model. Press the Select key under the Key Fob button to program. The following

listidentiesthedefaultbuttonassignments:

TOP Arming with no areas assigned

BTM Disarming with no areas assigned

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 77 78

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadian XR100 Manual de instrucciones Pagina 59

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadian XR100