Digital Monitoring Products Canadian XR100 Manual de instrucciones descargar pdf (Pagina 41)

XR100 Series Programming Guide Digital Monitoring Products

Output OptiOns

Output Options

11.1

OUTPUT OPTIONS

Output Options

This section allows you to program panel output options. The panel provides

twoFormCrelays(1and2)andfourswitchedground(opencollector)outputs

numbered3to6.UsetheJ22LX-Busonthepanelandmultiple716Output

ExpanderModulestosupportupto100additionalrelayoutputs.Alternately,when

using the 1100X wireless receiver, 45 wireless outputs are available. Refer to the

XR100SeriesInstallationGuide(LT-0899)forcompleteinformation.

Select from the following output numbers:

•1to6

•450to474—Slowresponsetime*wirelessoutputs(activateswithin15seconds)

•480to499—Fastresponsetime*wirelessoutputs(activateswithin1second)

•500to599—LX-Busoutput

•D1toD8—Keypaddoorstrikerelayforaddresses1-8

•G1toG20—Outputgroup

* The response time of a wireless output is the time it takes for a wireless output

to activate once the panel event occurs. You determine whether a wireless output

is a slow or fast response based on the output number assigned. A slow response

output number extends battery life, but response time may be up to 15 seconds.

A fast response output number responds within 1 second, but reduces battery life.

Refertothespecicwirelessoutputinstallationguidetodeterminebatterylife.

11.2.1

CO OUTS: - - - - - -

Cutoff Output

Outputs1to6canbeenteredheretoturnoffafteratimespeciedinCUTOFF

TIME.Todisablethisoption,pressanySelectkeytoclearthedisplaythenpress

COMMAND. The Cutoff Output displays dashes when no outputs are selected.

11.2.2

CUTOFF TIME: 0

Output Cutoff Time

IfaCutoffOutput(1-6)isassigned,enteraCutoffTimeof1to99minutesforthe

outputtoremainon.Enter0(zero)forcontinuousoutput.

11.3

COMM TRBL OUT: 0

Communication Trouble Output

EntertheoutputnumbertoturnonwhenaDDsystemfailstocommunicateon

three successive dial attempts or if the backup communication line transmits a

report.TheCommunicationTroubleOutputalsoturnsonwhenNETisselected

astheprimarycommunicationmethodandNETcommunicationfailsafterone

minute.WhenNETcommunicationisrestoredtheCommunicationTroubleOutput

automatically turns off.

To manually turn the output off, disarm any area or select Off for the output

numberintheUserMenuOutputsOn/Offsection.Enter0(zero)todisablethis

output.

11.4

FIRE ALR OUT: 0

Fire Alarm Output

Entertheoutputnumbertoturnonwhenaretypezoneisplacedinalarm.The

outputisturnedoffusingtheSensorResetoptionwhilenoadditionalretype

zonesareinalarm.Enter0(zero)todisable.Thisoutputisnotcompatiblewith

Cutoff Outputs.

11.5

FIRE TRB OUT: 0

Fire Trouble Output

Entertheoutputnumbertoturnonwhenaretypezoneisplacedintrouble,

when a supervisory type zone is placed in trouble, or when any system monitor

(AC,Battery,PhoneLine1orPhoneLine2)isplacedintrouble.Theoutputturns

offwhenallreandsupervisorytypezones,orsystemmonitorsarerestoredto

normal.Enter0(zero)todisablethisoutput.Thisoutputisnotcompatiblewith

CutoffOutputs.Thisoutputcanbeconnectedtoalamp,LED,orbuzzerusingthe

DMPModel716OutputExpansionModule.

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 77 78

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadian XR100 Manual de instrucciones Pagina 41

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadian XR100