Digital Monitoring Products Canadian XR100 Manual de instrucciones descargar pdf (Pagina 63)

XR100 Series Programming Guide Digital Monitoring Products

Zone InformatIon

18.16

OUTPUT: NONE

Output Action

EnteringanOutputNumberdisplaysthisoption.Thisoptionallowsyoutoassignan

output action to the relay: Steady, Pulse, Momentary, or Follow.

STD PLS MOM FOLW

STEADY - The output is turned on and remains on until the area is disarmed, an

output cutoff time expires, or the output is reset from the keypad menu.

PULSE - The output alternates one second on and one second off. Note: The

pulsingrateforaModel716relayattachedtotheLX-Busis1.6seconds.

MOMENTARY - The output is turned on only once for one second.

FOLLOW - The output is turned on and remains on while the zone is in an off

normal, or bad condition. When the zone restores, the output is turned off.

Note:ForDayZonetypes,whenanoutputisturnedon,ausercodewithsilence

authority can turn the output off.

After you make the three selections in the sections above, the display prompts you

for the same three selections for Disarmed Short, Armed Open, and Armed Short

conditions.Ifthezoneisa24-hourtype,onlytheArmedOpenandArmedShort

conditions display. When you have programmed all of the zone conditions, the

Swinger Bypass selection then dis plays.

18.17

SWGR BYP NO YES

Swinger Bypass

SelectingYESallowsthezonetobeswingerbypassedbythepanelaccordingtothe

specicationsprogrammedinSwingerBypassTripsandResetSwingerBypass.The

BypassconditiondisplaysinthekeypadStatusList.SelectingNOdisablesswinger

bypassing for this zone.

How it works

Ifwithinonehour,azonetripsthetotalnumberoftimesASspeciedinSwinger

Bypass Trips, the panel bypasses it until the following conditions occur; the area

in which the zone is assigned is disarmed, the zone is manually reset through the

BypassZones?keypadUserMenufunction,thezoneremainsnormalforonehour

andtheResetSwingerBypassisYES.

Ifthezonetripsfewerthanthespeciedtimeswithinonehour,thebypasstrip

counterreturnsto0(zero)andtheprocessmustberepeated.

AreportoftheswingerbypassissenttothereceiverifBypassReportsisYES.

Note: Not investigated by UL.

18.18

PREWARN KEYPADS:

Prewarn Keypad Addresses

Attheentrydelaystart,allkeypadaddressesselectedheredisplayENTERCODE:-.

Ifyouwanttheprewarntosoundatall8addresses,leavethedefaultsetting.

To delete an address, press the matching number on the keypad. To disable

prewarning at all keypads, press a top row Select key to clear the addresses shown.

Press the COM MAND key when the address selection is com plete.

Theprewarntonestopsatthekeypadwheretherstusercodedigitisentered.If

nokeysarepressedforvesecondsoraninvalidusercodeisentered,theprewarn

tone resumes at that keypad.

18.19

ENTRY DELAY: 1

Entry Delay

Selecttheentrytimerforthiszone.Entrytimers1to4areprogrammedinSystem

Options.

18.20

RETARD NO YES

Zone Retard Delay

WhenyouselectYES,thezoneoperateswiththezoneretarddelay.Theretard

func tions only in zone short condi tions.

The zone must re main shorted for the full length of the re tard de lay before the

panel recognizes its condition. If you select NO, the zone operates without a retard

delay.

Note: For UL installations, Zone Retard Delay shall not be used for burglary zones.

18.21

PRESGNL KEYPADS:

Presignal Keypad Addresses

You can enable any combina tion of keypad addresses to sound a presignal tone

during the time a zone is in retard delay. The presignal tone si lences when the zone

restores or the re tard delay expires.

To en able a presignal ad dress, press any top row Select key followed by the number

ofthekeypadaddress.Youcanenablethepresignalforall8keypadaddresses.

To disable a presignal address press the matching number digit again. Press the

COMMAND key when the address selection is complete. The Presignal option is only

displayedwhenRetardisselectedasYES.

A T L -

1 2 ... 58 59 60 61 62 63 64 65 66 67 68 ... 77 78

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadian XR100 Manual de instrucciones Pagina 63

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadian XR100