Digital Monitoring Products Canadian XR100 Guía de instalación descargar pdf (Pagina 24)

Digital Monitoring Products XR100 Series Canadian Installation Guide

InstallatIon

J1 Ethernet Connector (XR100N only)

16.1 Description

The J1 Ethernet Connector is available on the XR100N Network version to connect directly to an Ethernet network using a

standard patch cable. The maximum line impedance is 100 Ohms.

16.2 Ethernet LEDs

The two LEDs, located to the left of J1 Ethernet Connector, indicate network

connection. The top, Link LED lights up green to indicate a valid receive connection

fromthehostnetwork.Thebottom,ActivityLEDashesyellowtoindicatemessages

are being sent and received.

J3 Telephone RJ Connector

17.1 Description

Connect the panel to the public telephone network by installing a DMP 356 RJ Cable between the panel J3 connector and

the RJ31X or RJ38X phone jack. The maximum line impedance is 100 Ohms. CAUTION -Toreducetheriskofre,useonly

No.26AWGorlargertelecommunicationlinecord,suchasDMPModel356SeriesPhoneCords.

17.2 J10 893A Connector

Connect an 893A Dual Phone Line Module to J10 on the XR100 Series. Refer to the 893A Installation Sheet

(LT-0135) for complete information.

17.3 Notication

The user must not repair registered terminal equipment. In case of trouble, immediately unplug the device from the

telephone jack. The factory warranty provides for repairs. Registered terminal equipment may not be used on party lines

or in connection with coin telephones. No tify the telephone company with the following information:

a. The particular line(s) where the service is connected

b. This Class A digital apparatus complies with Canadian ICES-003.

c. The ringer equivalence

d. The device make, model, and serial number

17.4 Phone Line Monitor

The XR100 Series panel has a built-in telephone monitor that monitors the phone line voltage to verify the connection to

thecentralofce.Figure9andthetablebelowidentifythephoneblockpinlayout,wirenumbers,andcolors.

Wire Number Wire Color

1 Gray

2 Orange

3 Black

4 Red

5 Green

6 Yellow

7 Blue

8 Brown

ThewiresontheRJ31thatfeedpins4and5shouldbetheONLYwiresontheD-marc.Allotherhousephonewiringshould

be tied to pins 1 and 8 coming back from the RJ31.

DialtonemustcomeintoRJ31Xonpins4and5andgobacktohousephonesfrompins1and8.Followthesestepsto

determine if panel is seizing the line:

1. Unplug phone cord from RJ31X

2.Placebutt-setonpins4and5

3.Listenfordialtone.Withdialtonepresent,lifteitherwirefrompins1or8

4.Listenfordialtoneagain.Ifthedialtoneispresent,RJ31Xwiringiscorrect.Ifnodialtoneispresent,theRJ31X

wiringisbackwards.RewiresodialtoneiscomingINon4and5.

If you still have trouble with the phone line, you may need to replace the RJ cord. If the dial tone is still not present, swap

out the RJ31X phone block.

Figure 8: J1 Header and LEDs

Ethernet

Link LED

Activity LED

To Te lephone

Line

RJ31X or RJ38X

Phone Block

Ring Tip

To Premise

Phone

Ring 1

Tip 1

Figure 9: Phone Jack Wiring

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 35 36

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadian XR100 Guía de instalación Pagina 24

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadian XR100