Digital Monitoring Products XR550 Manual de instrucciones descargar pdf (Pagina 51)

XR150/XR350/XR550 Series Programming Guide Digital Monitoring Products

AREA INFORMATION

17.13 Automatic Arming

Select YES to allow this area to arm automatically according to permanent, temporary, or

extended schedules. If no schedules are programmed, the area auto arms every hour.

If closing check is selected as YES, the automatic arming function does not take place until

the expiration of a ten minute Closing Check delay. See Closing Check. If the area has been

disarmed outside of any permanent or temporary schedule, the closing check sequence

occurs one hour after the area is disarmed.

At arming, bad zones are handled according to the option selected in section Bad Zones.

If a closing report is sent, the user number is indicated as SCH on the SCS-1R Receiver. NO

disables automatic arming for this area.

Note: For ANSI/SIA CP-01 UL installations, Automatic Arming cannot be used for arming.

17.14 Bad Zones

At the time of automatic arming, some zones in the area may not be in a normal condition.

This option allows you to program the panel response to these bad zones. This option does

not display if AUTO ARM is NO.

BYP - All bad zones are bypassed. A report of the bypass is sent to the receiver if Bypass

Reports is YES. The report indicates SCH as the user number.

FORC - All bad zones are force armed. Zones force armed in a bad condition are capable

of restoring and reporting an alarm if tripped. A forced zone report is transmitted if Bypass

Reports is YES. The report indicates SCH as the user number.

REF - The automatic arming is refused and no arming takes place. A No Closing report is

sent to the receiver regardless of the Closing Check selection.

17.15 Automatic Disarming

NO disables automatic disarming by schedule for this area. When YES is selected, the area

automatically disarms according to permanent or temporary schedules. If an opening report

is sent to the receiver, the user number is indicated as SCH.

17.16 Armed Output Number

Enter the output to turn on when this area is armed. If an exit delay is used for this area,

the Armed Output turns on at the start of the exit delay. The output is turned off when

this area is disarmed. The output cannot be turned on from the User Menu Outputs On/Off

option.

17.17 Late Output Number

Enter the output to turn on when this area is not armed by its scheduled time and Area

Late or Closing Time displays at a keypad and the keypad buzzer is on. The output is turned

off when the keypad buzzer is silenced by pressing any key. Default is 0 (zero).

17.18 Late Arm Delay

Enter 4 to 250 minutes to delay before automatic re-arming occurs after the area becomes

disarmed outside of schedules. See Closing Check. Default is 60 minutes.

Note: The Late Arm Delay can be superseded by the Re Arm Delay setting of the User

Prole assigned to the user who disarmed the area. Refer to the Re Arm Delay section in

the XR150/XR350/XR550 Series User’s Guide (LT-1278).

17.19 Bank Safe & Vault (XR550 with Network or Encryption only)

NO disables the Bank Safe & Vault feature for this area. When selected as YES, schedules

set for any area and the time of day cannot be changed while the area is armed.

Program schedules before arming: A Bank Safe & Vault area can only be disarmed during

scheduled times. If the area becomes armed before programming a schedule, the panel

must be reset before the area can be disarmed from a keypad or the Bank Safe & Vault

option in Area Information must be set to NO.

Zones assigned to Bank Safe & Vault areas cannot be bypassed or force armed. Do not

assign Bank Safe & Vault area to an Arming zone. Arming zones can disarm Bank Safe &

Vault areas outside of a schedule.

17.20 Common Area

Select YES to enable this area to operate as a common area. This area is armed when

the last area in the system is armed and is disarmed when the rst area in the system is

disarmed. You can have multiple common areas in each system. For the common area to

work properly, do not assign the common area to any user code. When a user code can

arm and disarm the common area from a keypad at any time, the common area does not

function as a common area.

AUTO ARM NO YES

BAD ZONES: BYP

BYP FORC REF

AUTO DIS NO YES

ARMED OUTPUT: 0

LATE OUTPUT: 0

LATE/ARM DLY: 60

BANK/SAF NO YES

COMMON NO YES

1 2 ... 46 47 48 49 50 51 52 53 54 55 56 ... 77 78

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products XR550 Manual de instrucciones Pagina 51

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products XR550