Digital Monitoring Products XR550 Manual de instrucciones Pagina 36
- Pagina / 78
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide
26
SYSTEM OPTIONS
9.13 Latch Supervisory Zones
Selecting YES latches supervisory zone alarms on the keypad display until the sensor reset
operation is performed. Selecting NO automatically clears the alarm from the
keypad
display when the supervisory zone restores to a normal condition. Default is YES.
9.14 Programming Menu Language
Press the COMMAND key to select the programming language. Any changes in PROG
LANGUAGE do not take effect until the STOP routine completes.
The current primary programming language displays. The default language is English. Press
a Select key to change the primary programming language.
Select the primary programming language.
ENG = English (ENGLISH)
SPN = Spanish (ESPANOL)
FRN = French (FRANCAIS)
The current secondary programming language displays. Selecting a secondary language
allows the installer to view programming in English, Spanish, or French. When the
Programming Menu is accessed, the installer is prompted to choose the programming
display language. If SEC LANG: is set to NONE, the option to choose a language does not
display. To select a secondary language, press the Select key below the language.
Default is NONE.
Select the secondary programming language.
NONE = No secondary language options are displayed
ENG = English (ENGLISH)
SPN = Spanish (ESPANOL)
FRN = French (FRANCAIS)
9.15 User Menu and Status List Language
Press the COMMAND key to select User language.
The current primary user language displays. The default language is English. Press a Select
key to change the primary User language.
Select the primary user language.
ENG = English (ENGLISH)
SPN = Spanish (ESPANOL)
FRN = French (FRANCAIS)
The current secondary user language displays. Selecting a secondary user language allows
the user to view the User Menu and Status List text in English, Spanish, or French. When
the User Menu is accessed, the user is prompted to choose the display language.
Status List text displays in the selected language until another language is chosen. If
SEC LANG: is set to NONE, the option to choose a language does not display. To select a
secondary language, press the Select key below the language. Default is NONE.
For example, when Spanish is selected at a keypad, the User Menu and Status List text
display in Spanish at that keypad. When the user later accesses the keypad, pressing
the COMMAND key once displays the option for English, Spanish, or French. Pressing the
COMMAND key again continues to display the Status List text in Spanish. Later on, if English
or French is selected at that keypad, the User Menu and Status List text display in the
selected language at that keypad.
Select the secondary user language.
NONE = No secondary language options are displayed
ENG = English (ENGLISH)
SPN = Spanish (ESPANOL)
FRN = French (FRANCAIS)
9.16 Bypass Limit
Enter the maximum number of zones (0 to 8) that can be bypassed in any single area when
that area is being armed at a keypad. If more zones than the limit are in a non-normal
state or already bypassed at arming, arming does not occur and Arming Stopped displays.
The Bypass limit does not affect auto arming, keyswitch arming, or remote arming.
Entering 0 (zero) allows no limit. Default is 0 (zero).
9.17 House Code
When using a DMP wireless system, enter a house code between 1 and 50. See Wireless
programming in Zone Information. Default is 0 indicating no wireless system is being used.
The DMP house code identies the panel, DMP receiver, and DMP transmitters to each other.
When operating, the DMP receiver listens for transmissions that have the programmed
house code and transmitter serial number.
Note: The exibility of DMP two-way wireless operation allows an existing house code to
be changed in the panel at any time. The transmitters may take up to two minutes to learn
the new house code and continue operation.
Note: When any wireless zone programming is changed in the panel, wireless receiver
zone programming is updated. At that point, all wireless zones display as normal for
approximately 1 minute, regardless of the actual state of the zone.
LATCH SV NO YES
PROG LANGUAGE
PRI LANG: ENGLSH
ENG SPN FRN
SEC LANG: NONE
NONE ENG SPN FRN
USER LANGUAGE
PRI LANG: ENGLSH
ENG SPN FRN
SEC LANG: NONE
NONE ENG SPN FRN
BYPASS LIMIT 0
WIRELESS
HOUSE CODE: 0
- PROGRAMMING GUIDE 1
- TABLE OF CONTENTS 10
- Introduction 11
- COMMAND (CMD) Key 13
- Back Arrow (<—) Key 13
- Select Keys/Areas 13
- Special Character 14
- First Letter 14
- Second Letter 14
- Third Letter 14
- YESBELL TST 15
- NOBELL TST 15
- Initialization 16
- Communication 17
- COMMUNICATION 21
- 3.33 Send Path Information 21
- (Network or Encryption Only) 22
- Messaging Setup 23
- Device Setup 24
- Remote Options 30
- 000.000.000.000 31
- System Reports 33
- System Options 34
- Bell Options 39
- Output Options 40
- Output Information 43
- Output Groups 44
- Menu Display 45
- Status List 46
- PC Log Reports 48
- Area Information 49
- AREA INFORMATION 52
- 17.21 Arm First Area 52
- Zone Information 53
- Set Lockout Code 63
- Feature Upgrade 64
- Appendix 65
- APPENDIX 66
- 22.4 Using the Walk Test 68
- Walk Test 68
- Zone Types 68
- Bell Action 69
- Trip Counter For Walk Test 69
- Test End Warning 69
- See Figure 10 70
- 22.9 UserProlesRecord 71
- 22.12.1 73
- Keypad Bus Zone Type Defaults 73
- LX-Bus Zone Type Defaults 74
- 22.13 Common Keypad Messages 75
- Certications 78
- Export Control 78
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products XR550
(31 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales