Digital Monitoring Products Canadain XR500 Guía de instalación descargar pdf (Pagina 29)

XR500 Series Canadian Installation Guide Digital Monitoring Products

ComplianCe

22.3 For Low Risk Applications: Level A1

LevelA1communicationchannelsecurityisprovidedforInternet,Intranet,LANorWANnetworkswhenconguredas

a NET communicating system using the XR500N.

22.4 For Low Risk Applications: Level P1

LevelP1communicationchannelsecurityisprovidedwhenconguredasaDDcommunicatingsystemandadailytest

message using the XR500.

22.5 Dual Protection

For Medium or High Risk ULC Listed Applications: Use only zones 1-8 on the control panel and program Dual EOL as

Yes in panel programming. Program the Disarmed Short Message in Alarm Action of Zone Information programming as

a Trouble message.

Ifusinga714,714-8,or714-16fordualprotection,programtwozonesasthesamenameorequivalentandconnect

to the contact in the protected area as show in the Dual Zone Protection diagram in the back of this guide.

22.6 Remote Arming

For ULC Listed applications, remote arming is not permitted.

22.7 Zone Expansion

Use of the following zone expanders are permitted for connection of burglary devices:

710 Bus Splitter Module 714ZoneExpander,4zones 715ZoneExpander,4zones 7070(A)/7073(A)Keypads,4zones

711 Zone Expander, Single 714-8ZoneExpander,8zones 715-8 Zone Expander, 8 zones 7170/7173Keypads,4zones

712-8 Zone Expander, 8 714-16ZoneExpander,16zones 715-16 Zone Expander, 16 zones

ULC S559-04 Specications

Equipment for Fire Signal Receiving Centers and Systems

23.1 For Fire Communicator Applications

Forrecommunicatorapplications,communicationtotheresignalreceivingcenterisprovidedforInternet,

Intranet,LANorWANnetworkswhenconguredasaNETorCELLcommunicatingsystemusingtheXR500Series

panel. See wiring diagram in section 26.5 for additional information. Program one of the following options in panel

Communication:

Path 1 Type NET or CELL Primary with no Backup

Path 1 Programming

Comm Type = NET or CELL Checkin Min = 3

Path Type = Primary Failtime Min = 3

Sub Code = No Send Comm Trbl = Yes

Comm Path Trbl = Yes (Status List Programming)

Path 1 Type NET Primary and Path 2 Type CELL Backup

Path 1 Programming Path 2 Programming

Comm Type = NET Comm Type = CELL

Path Type = Primary Path Type = Backup

Test Rpt = Yes Test Rpt = Yes

Test Freq = 1 Dy Test Freq = 1 Dy

Send Comm Trbl = Yes Send Comm Trbl = Yes

Comm Path Trbl = Yes (Status List Programming)

23.2 Central Station Host Automation

Theresignalreceivingcenter’shostautomationsystemmustrecognizethefollowingsignals:Zone1Alarm=Fire

Alarm,Zone2Trouble=FireZoneTrouble,Zone3Trouble=ACTrouble,Zone4Trouble=BatteryTrouble,andZone

5Trouble=GroundFaultTrouble.

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 39 40

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Guía de instalación Pagina 29

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500