Digital Monitoring Products Canadain XR500 Guía de instalación descargar pdf (Pagina 25)

XR500 Series Canadian Installation Guide Digital Monitoring Products

InstallatIon

15.3 LX-Bus Interface Cards

YoucanaddoneInterfaceCard(Model481,462N,462P,or464-263H)totheXR500SeriesusingJ6InterfaceCard

Connectorlocatedontheboardrightedge.ToaddmorethanoneInterfaceCardinstalla461InterfaceAdaptorCard

usingJ6InterfaceCardConnectorontheboardrightedge.The461AdaptorCardallowsuptoveInterfaceCards

tobeinstalled.Refertothe461InstallationSheet(LT-0736).EachInterfacecardprovidesupto100LX-BusZones.

Refer to the following tables to identify zone locations and numbers relative to J22 operation.

J22 LX-Bus Enabled

(Set J23 to “L”)

AND

One Interface Card

461 Adaptor Card and

Multiple Interface Cards

LX-Bus Zone Numbers LX-Bus Zone Numbers LX-Bus Zone Numbers

1 500-599 2 600-699 2 (A) 600-699

3 (B) 700-799

4(C) 800-899

5 (D) 900-999

J22

LX-Bus

NOT

Enabled

(J23

NOT set

to “L”)

One Interface Card

461 Adaptor Card and

Multiple Interface Cards

LX-Bus Zone Numbers LX-Bus Zone Numbers

1 500-599 1 (A) 500-599

2 (B) 600-699

3 (C) 700-799

4(D) 800-899

5 (E) 900-999

15.4 LX-Bus LEDs

The two LEDs, located near the bottom-right corner of J21 indicate data transmission and receipt. The top LED

ashesgreentoindicatethepanelistransmittingLX-Busdata.ThebottomLEDashesyellowtoindicatethepanel

is receiving LX-Bus data.

15.5 OVC LED

TheOvercurrentLED(OVC)lightsRedwhenthedevicesconnectedtotheKeypadBusandLX-Bus(es)drawmore

current than the panel rating. The OVC is located above Outputs 1 and 2 on the panel and turns a steady Red when

lit.WhentheOVCLEDlightsRed,theLX-Bus(es)andKeypadbusshutdown.

J21 Serial Connector

16.1 Description

Note: Only one connector, J21 or J22 can function at a time. Either use J21 to connect a serial device for PC Log

Reporting,oruseJ22toconnectaDMPWirelessdeviceoranLX-Busdevice.Operationisdeterminedbywhereyou

install the jumper on the J23 6-Pin header. The maximum line impedance is 100 Ohms.

To enable J21 to operate in RS-232 mode, place a jumper on the two pins next to the letter “R” on the J23 6-Pin

headerandbrieyresetthepanelusingtheJ16jumpertoactivatetheselectedoperation.Panelprogrammingusing

Remote Link™ can be set up through a direct connection to a computer. The Serial Connector allows the following

operation options.

XR500 Panel XR500N/XR500E Panel

PC Log Reports PC Log Reports

Remote Link™

Programming

16.2 Computer Connection to J21

Use a straight through RS-232 Serial cable with a DB-9 female connector on one end and a DB-9 male connector on

the other end. Plug the DB-9 male connector end of the cable onto the XR500 Series panel J21 RS-232 connector.

Plug the DB-9 female connector end of the cable onto the DB-9 male connector located at the back of the computer.

Program the XR500 Series panel as needed then disconnect the computer.

16.3 Serial Connector LEDs

The two LEDs, located near the bottom-right corner of J21 indicate data transmission and receipt. The top LED

ashesgreentoindicatethepanelistransmittingserialdata.ThebottomLEDashesyellowtoindicatethepanelis

receiving serial data.

Serial Data Xmit LED

Serial Data Rec(eive) LED

J22

J23

J21

RS-232

DB-9 Female Connector

Figure 9: J21 Serial Connection

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 39 40

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Guía de instalación Pagina 25

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500