Digital Monitoring Products Canadain XR500 Guía de instalación descargar pdf (Pagina 23)

XR500 Series Canadian Installation Guide Digital Monitoring Products

InstallatIon

Dry Contact Relay Outputs

12.1 Description

The XR500 Series panel provides two programmable auxiliary SPDT relays when equipped with two DMP Model 305

relaysinsocketsK6(Output1)andK7(Output2)andaModel431OutputHarnessontheJ26-pinHeader.Eachrelay

provides one SPDT set of contacts that can be operated by any of the functions listed below:

1) Activation by zone condition: Steady, Pulsing, Momentary, and Follow

2)Activationby24-hour7-dayschedule:Oneonandoneofftimeadayforeachrelay

3) Manual activation from the DMP LCD keypad menu

4)Communicationfailure 8)ExitandEntrytimers

5) Armed area annunciation 9) System Ready

6) Fire Alarm, Fire Trouble or Supervisory 10) Late to Close

7) Ambush Alarm

RefertotheXR500SeriesCanadianProgrammingGuide(LT-0679CAN)forspecicinformation.

12.2 Contact Rating

The Model 305 relay contacts are rated for 1 Amp at 30 Vdc (allows .35 power factor). You can connect auxiliary

power to the Relay Output 1 common terminal by installing the gray harness wire to terminal 7. Current draw for all

connected devices must not exceed the panel maximum current rating.

12.3 Model 431 Output Harness Wiring

TherelaycontactsareaccessiblebyinstallingtheDMP431OutputHarnessonthe6-pinheaderlabeledJ2.Output

2 uses the top three prongs, and Output 1 uses the bottom three prongs. The wire harness and contact locations are

shown below:

Contact Color

Output 1 normally closed Violet

Output 1 common Gray

Output 1 normally open Orange

Output 2 normally closed Violet with white stripe

Output 2 common Whitewithgraystripe

Output 2 normally open Orange with white stripe

The relay contacts must be connected to devices located within the same room as the XR500 Series panel.

Annunciator Outputs

13.1 Description

The four programmable annunciator outputs can be programmed to indicate the activity of the panel zones or

conditions occurring on the system. Annunciator outputs do not provide a voltage but instead switch-to-ground a

voltage from another source. The outputs can respond to any of the conditions listed in the Description section for

Dry Contact Relays. Maximum voltage is 30 Vdc @ 50mA.

13.2 Model 300 Harness Wiring

AccesstheopencollectoroutputsbyinstallingDMP300Harnessonthe4-pinheaderlabeledJ11.Theoutput

locations are shown below. For listed applications, devices connected to the outputs must be located within the

same room as the panel.

Output Color Wire Output Color Wire

3 Red 1 5 Green 3

4 Yellow 2 6 Black 4

13.3 Model 860 Relay Module

Connect a Model 860 Relay Module to the J11 on the XR500 Series Canadian panel to provide relays for outputs

3-6. Use these relays for electrical isolation between the alarm panel and other systems or for switching voltage to

control various functions. Power is supplied to the relay coils from a single wire connected to the panel auxiliary

power terminal 7. The module includes one relay and provides three additional sockets for expansion of up to four

relays. Mount the 860 inside the panel enclosure using the 3-hole pattern and plastic standoffs. Refer to the 860

ModuleInstallSheet(LT-0484)asneeded.

Relay Contact Rating: 1 Amp at 30 Vdc (allows .35 power factor)

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 39 40

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Canadain XR500 Guía de instalación Pagina 23

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Canadain XR500