Digital Monitoring Products XTL Series Guía de instalación descargar pdf (Pagina 9)

XTL/XTLC Installation Guide Digital Monitoring Products

InstallatIon

LED Operation

7.1 Backlit Logo

ThebacklitlogoindicatesthePowerandArmedstatusofthepanel.Dependingontheoperation,theLED

displaysinRedorGreenaslistedinthetable.

Color and Activity Operation

GreenSteady PanelDisarmed,PrimaryPowerOK,BatteryOK

GreenBlinking PanelDisarmed,PrimaryPowerOK,BatteryFault

NoLight PanelDisarmed,PrimaryPowerFault,BatteryOK

Red Steady PanelArmed,PrimaryPowerOK,BatteryOK

Red/GreenAlternate PanelArmed,PrimaryPowerOK,BatteryFault

RedBlinking PanelArmed,PrimaryPowerFault,BatteryOK

Reset Button

8.1 Description

Theresetbutton(S1)islocatedontherightsideofthecircuitboardandisusedtoresettheXTL/XTLC

microprocessor. To reset the panel prior to reprogramming, press the reset button without powering down

thesystem.Afterresettingthepanel,beginprogrammingwithin30minutes.Ifyouwaitlongerthan30

minutes, you must reset the panel again.

Programming Connection

9.1 Programming Connection

Alocking4-pinheader(PROG)isprovidedtoconnectakeypadwhenusingaDMPModel330Programming

Cable.Thisprovidesaquickandeasyconnectionforprogrammingthepanel.Afterprogrammingis

complete,removethekeypad.

Installing the 738Z

Toconnectthewiringofthe738ZtothePROGheaderofthepanel,useaPC-0140ConnectorAssembly

(includedwiththe738Z)forconnectionofaModel300harness.The738Zonlyoperateswhenprimarypower

is present.

Note:ThePROGheaderisnotintendedtoprovideaKeypadDataBusconnection.Theprogrammingkeypad

isoperationalonlywhenprimarypowerisappliedtotheXTL/XTLC.

On-Board 1100 Series Wireless

10.1 Wireless Antenna

TheXTL/XTLCWirelessAntennaisintegratedintothecircuitboard.Thebuilt-inwirelessreceiveroperates

withDMP1100Seriestransmitters.Seesection3.1foralistofaccessorydevices.

10.2 Wireless LED Operation

Green (TX):ThegreenLEDasheseverytimethereceivertransmits(32timespersecond).Ifthepanel

isreset,orthepanelispoweredoff,thegreenLEDisoff.Undernormaloperation,thegreenLEDashes

constantly with no interruption or change.

Yellow (RX):TheyellowLEDasheseverytimetheXTL/XTLCreceivesamessagefromaprogrammed

wirelesstransmitter.Whenamessageissentbyatransmitter,typicallybypressingorreleasingthetamper

switch,theyellowLEDshouldashindicatingthatthepanelreceivedamessagefromthetransmitter.

IftheLEDneverashes,thetransmitterisnotgettingthroughtothepanel.Thiscouldbebecauseofa

misprogrammedserialnumberorthetransmitteristoofaraway.Undernormaloperation,theyellow

LEDashesateverytripofeverywirelesstransmitterandwhenthetransmittersperformtheirperiodic

check-in.ItisnotunusualforthisLEDtostayoffformanyminutesatatimewhennotransmittersare

communicating.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products XTL Series Guía de instalación Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products XTL Series