Digital Monitoring Products Graphic Touchscreen Keypad Guía de instalación descargar pdf (Pagina 1)

InstallatIon GuIde

7760 LCD Glass Keypad

Description

The DMP Model 7760 LCD Glass Keypad offers the same functionality and exible features as standard DMP keypads.

The contemporary glass touch design offers an elegant, sleek look to accent any decor. Each 7760 keypad provides a

32‑character touchscreen backlit display, keyboard with easy‑to‑read lettering, three Panic icons, a multi‑functional AC

Power/Armed LED, and an internal speaker.

Installing the Keypad

The keypad housing is designed to easily install using two #6 screws on a at surface or optional 778 backplate. The

keypad housing is made up of two parts: a hinged cover and a base which contains the circuit board, glass touchscreen,

and keyboard components. A single 4‑wire harness is used to connect the 7760 to the keypad bus of a DMP control panel.

Figure 2 shows the back of the keypad with the 4‑wire harness connected.

Remove the Cover

Use the following steps and Figures 1 and 2 to remove the

hinged keypad cover.

1. Insert a at screwdriver into one of the slots on the

bottom of the keypad and gently lift the screwdriver

handle toward you while pulling the halves apart.

Repeat with the other slot.

2. Using your screwdriver, gently separate the left and

right sides of the cover by applying slight inward

pressure along the seam to disengage the internal

side snaps.

3. Gently lift the cover and remove from the four cover

hinges at the top and set aside.

Install the Base

Use the following steps to install the keypad base. Cut off the template below to use for mounting.

1. Place the template on the wall where the keypad is to be mounted and level using the horizontal alignment line.

2. Mark the two #6 screw locations and the wiring harness opening locations on the wall.

3. Install the two supplied #6 wall anchors where marked.

4. Drill a wiring harness hole no larger than 1/4” in diameter where indicated. Feed the 4‑conductor wire through

the created opening.

Note: Make sure the wire harness opening is small enough to be covered by the keypad base.

5. Connect the 4‑wire harness to the 4‑conductor Keypad bus wire from the wall.

6. Gently plug the 4‑wire harness connector onto the 4‑pin header through the opening in the back of the keypad.

See Figure 3.

7. Mount the 7760 keypad base to the #6 wall anchors using the provided #6 screws.

Replace the Cover

Use the following steps to reinstall the keypad cover.

1. Gently realign the top four hinges and set the cover into place.

2. Lower the cover and gently snap the two bottom latches and two internal side latches into place by squeezing the

base and cover together to reduce the stress on the legs. (See Figure 3)

Mounting Template

Drill 1/4" Hole for the Wiring Harness

Horizontal Alignment Line

#6 Screw

Location

#6 Screw

Location

✁

Cut along dotted line and use as a drill template to create mounting and wiring holes.

Figure 1: Loosen bottom

of cover

Legs

Glass

Keypad

Front

Building

Wall

778

Backplate

Lift screwdriver

handle up

toward you to

separate keypad

cover from base.

Figure 2: Loosen side

of cover

1 2 3 4 5 6

Indice de contenidos

Pagina 1 - 7760 LCD Glass Keypad

InstallatIon GuIde7760 LCD Glass KeypadDescriptionThe DMP Model 7760 LCD Glass Keypad offers the same functionality and exible features as standard D

Pagina 2 - Additional Power Supply

Digital Monitoring Products 7760 Keypad Installation Guide2Harness WiringFigure 3 shows wiring harness mounting location and wiring assignments. Obs

Pagina 3 - Panic Icons

7760 Keypad Installation Guide Digital Monitoring Products3Keypad Bus MonitorFor Fire Protective systems, the 893/893A Module must be installed in th

Pagina 4 - Internal Speaker Operation

Digital Monitoring Products 7760 Keypad Installation Guide4Internal Speaker OperationThe Glass keypad emits standard tones for key touches, entry del

Pagina 5 - Installer Options Menu

7760 Keypad Installation Guide Digital Monitoring Products5You can use the keyboard to enter alpha characters and special, non‑alpha characters. To

Pagina 6

Mas documentos para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Graphic Touchscreen Keypad

a Ver el documento Digital Monitoring Products Graphic Touchscreen Keypad Manual de usuario

Digital Monitoring Products Graphic Touchscreen Keypad Manual de usuario (4 paginas)

Comentarios a estos manuales

Sin comentarios

Digital Monitoring Products Graphic Touchscreen Keypad Guía de instalación Pagina 1

Busca en linea o descarga Guía de instalación para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Graphic Touchscreen Keypad. Digital Monitoring Products Graphic Touchscreen Keypad Installation guide Manual de usuario

Indice de contenidos

Mas documentos para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Graphic Touchscreen Keypad

Comentarios a estos manuales

Digital Monitoring Products Graphic Touchscreen Keypad Guía de instalación Pagina 1

Busca en linea o descarga Guía de instalación para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Graphic Touchscreen Keypad. Digital Monitoring Products Graphic Touchscreen Keypad Installation guide Manual de usuario

Indice de contenidos

Mas documentos para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Graphic Touchscreen Keypad

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digital Monitoring Products Graphic Touchscreen Keypad